Replacement of lowering glass. AZLK 2141 (Muscovite)
Service and car repairs of 2141 - the Muscovite.
1. General data
2. Engines
3. Power supply system
4. Cooling system
5. Transmission
6. Running gear
7. Tires, wheels
8. Steering
9. Brake management
10. Body
10.1. Features of a design of bodies of cars of fashion. 2141-01, 2335 and their modifications
10.2. Body fittings
10.2.1. Removal of an upholstery of side doors
10.2.2. Window regulators
10.2.3. Replacement of lowering glass
10.2.4. Possible malfunctions of side doors
10.2.5. Replacement of glasses
10.2.6. Locks and drives of locks of side doors
10.2.7. Replacement of springs of the external handle of a side door
10.2.8. Replacement of the switch of locks of a forward door
10.2.9. Possible malfunctions of locks and drives of side doors
10.2.10. Lock of a cowl and its drive
10.2.11. The body back door lock like "hatchback" and its drive
10.2.12. Replacement of locks of a back board of a body like "pickup"
10.2.13. Removal, installation and adjustment of side doors
10.2.14. Removal of a back door of a body like "hatchback"
10.2.15. Removal, installation and adjustment of a cowl
10.2.16. Removal and installation of a door of a back of a body like "hatchback"
10.2.17. Removal and installation of a back board of a platform of a body like "pickup"
10.2.18. Facing of a radiator
10.2.19. Removal and installation of the forward buffer
10.2.20. Removal and installation of the back buffer of a body like "hatchback"
10.2.21. Removal and installation of the back buffer of a body like "pickup"
10.2.22. Removal and installation of forward wings
10.3. Dashboard
10.4. Ventilation and heating
11. Electric equipment
12. Electrical circuitries
 










fd148775

10-2-3-zamena-opusknogo-stekla.html

10.2.3. Replacement of lowering glass

Installation of lowering glass of a forward door
1 – bolt of fastening of lowering glass;
2 – holder of a sealant;
3 – sealant;
4 – fillet;
5 – glass;
6 – slip;
7 – the valve is moisture protective small;
8 – adhesive tape;
9 – valve moisture protective big

Lowering glass of a forward door

1 – holder;

2 – glass;

3 – laying flew down;

I – a profile of the corrected holder of lowering glass

Lowering glass of a back door

1 – holder;

2 – laying flew down;

3 – glass

PERFORMANCE ORDER
1. When replacing lowering glass 5 (see rice. Installation of lowering glass of a forward door) it is necessary to execute the following.
2. To remove the upholstery of a door, details which are on it and moisture protective valves.
3. To remove the internal lower sealant 3 lowering glasses fastening to the top flange four spring holders 2 and an external subwindow slip 6. For renting of a sealant and a slip it is enough to pull of them for one edge up and to overcome resistance of the fixing short moustaches on holders 2 and on a metal part of a slip.
4. To disconnect glass from a window regulator for what to turn off two bolts 1, holding at the same time glass. At an otvorachivaniye of bolts to arrange glass on height so that heads of bolts settled down at the level of assembly openings in the internal panel of a door.
5. To develop the disconnected glass in a door to an exit it from a fillet 4, to lift and take out outside through a groove in the top part of a door. If renting of lowering glass from a door causes difficulties, then previously remove a window regulator.
6. To sort the taken-out glass for what to insert the screw-driver into a gap between glass 2 (see rice. Lowering glass of a forward door) both a holder of 1 forward door, and, respectively, glass 3 (see rice. Lowering glass of a back door) and holder of 1 back door.
7. Then to correct a holder. Groove width in a holder under glass has to be: above — 7,5 mm, below — 8,5 mm (see rice. Lowering glass of a forward door).
8. To press new lowering glass with rubber laying in the corrected holder as it is shown on rice. Lowering glass of a forward door and rice. Lowering glass of a back door. To make a press fitting of glass on the press with manual giving or by means of the hammer.
9. In the latter case to rest glass the top part against a wooden support, having enclosed previously soft laying. To impose rubber laying on an edge of glass 3 (see rice. Lowering glass of a forward door) and 2 (see rice. Lowering glass of a back door) I will also embrace, after that blows of the hammer through wooden whetstone to press glass against the stop.
10. Then to cut off laying flush with edges of a holder. Correctly pressed glass should not move forward from a holder by effort of hands.
11. To insert the repaired glass in a door through the groove which is available in the top part of a door, having developed glass for simplification of its input inside.
12. To lower the ram of a window regulator and profit bolts 1 (see rice. Installation of lowering glass of a forward door) through the lower assembly openings in the internal panel of a door.
13. To lift glass rotation of the handle of a window regulator to the level of the top assembly openings, it is correct to expose glass on a frame and to finally tighten bolts.



10.2.2. Window regulators

10.2.4. Possible malfunctions of side doors