|
10-2-12-zamena-zamkov-zadnego-borta-kuzova-tipa-pikap.html
10.2.12. Replacement of locks of a back board of a body like "pickup"Installation of locks and the drive of locks of a back board of a body like "pickup"
1 – lock of a back board;
2 – holder of drafts of the drive of locks;
3 – draft of the drive of locks;
4 – drive of locks of a back board;
5 – latch of the lock of a back board;
|
6 – washer of the 10th fastening of a latch;
7 – bolt of M6-6 x 35th fastening of the lock;
8 – bolt of M6 x 16th fastening of the drive of locks;
9 – laying of a back board of a platform |
The lock of a back board of a body like "pickup"
|
1 – fork axis;
2 – fork spring;
3 – fork clamp axis;
4 – fork clamp;
5 – plate;
|
6 – fork;
7 – lock case;
8 – rivet of fastening of the lever
drive;
9 – lever of the drive of the lock of a back board |
Because locks of a back board (right and left) a cargo platform have a non-demountable design, in case of failure it is necessary to make their replacement.
| PERFORMANCE ORDER |
| 1. To open a back board of a platform. |
| 2. To remove the upholstery of a back board of a platform fixed by screws. |
3. Through assembly openings in the amplifier of a back board to disconnect from the lock 1 lever (see rice. Installation of locks and the drive of locks of a back board of a body like "pickup") draft of the drive 3 for what to turn in a lever opening 1 plastic holder 2 at a size providing a descent of a spring mustache of the holder from draft 3 and to take out the last from the holder.
|
| 4. To unscrew two screws 7 of fastening of the lock to a board and to remove the lock. |
| 5. Having squeezed short moustaches of a cutting shaft of the holder 2 at a necessary size, to take out it from a lock lever opening. |
| 6. Installation of the lock is made in the return sequence. |
|
The lock has a non-demountable design, however, in urgent cases (lack of the new lock) and presence of sufficient metalwork skills at the performer, it is possible to make his dismantling for the purpose of repair at break of an internal spring of the lock or easing in it the rolled connections.
Dismantling
| PERFORMANCE ORDER |
| 1. Any sharp tool it is accurate to straighten a razvaltsovanny conic part of an axis of a clamp of a fork 3 (see rice. The lock of a back board of a body like "pickup") and axes of a fork 1. |
| 2. Then a suitable mandrel to beat out axes 1 and 3 of openings of a plate 5 and to disassemble the lock. |
| 3. Having replaced the broken spring of a fork 2 and having restored reliability of the rolled connections in the lock, to assemble it in the return sequence. |
| 4. The conic parts of axes 1 and 3 which are previously straightened when dismantling can be razvaltsevat in openings of a plate 5 by means of the conical mandrel which is picked up for the size and the hammer, having rested the opposite ends of axes against a strong and massive support. |
| 5. After flaring the radial free wheeling and a provorachivaniye of axes are not allowed. |
| 6. At emergence of a side play of the lever of the drive 9 it is necessary to razvaltsevat in addition rolled end of a rivet of fastening of the lever 8 accurate blows of the hammer, having rested the opposite end of a rivet against a strong and massive support. |
| 7. Flaring should not create the effort interfering movement of the lever of the drive 9 concerning a plate 5. |
|
|
|
