Steering assembly. AZLK 2141 (Muscovite)
Service and car repairs of 2141 - the Muscovite.
1. General data
2. Engines
3. Power supply system
4. Cooling system
5. Transmission
6. Running gear
7. Tires, wheels
8. Steering
8.1. Features of a design of steering
8.2. Check of technical condition of steering on the car
8.3. Steering adjustment
8.4. Steering assembly
8.5. Spherical hinges of steering drafts
8.6. Technical condition of the driveshaft and a steering column before dismantling
8.7. Dismantling, check of technical condition and assembly of the driveshaft
8.8. Possible malfunctions of steering
9. Brake management
10. Body
11. Electric equipment
12. Electrical circuitries
 










fd148775

8-4-sborka-rulevogo-upravleniya.html

8.4. Steering assembly

Assembly of the steering mechanism has to be carried out accurately and carefully, in the conditions of full purity as it is one of the main knots defining traffic safety.

Installation of bearings should be made by means of mandrels, putting effort only to an external ring at a press fitting in an opening and only to internal at a napressovka on a shaft.

PERFORMANCE ORDER
1. To press the basic plug 47 (see rice. Steering) in a case pipe a rubber fringing outside.
2. To press the roller bearing 63 so that the bearing end face from consolidation was aflush with torets of a case.
3. To Napressovat the ball bearing 67 on a gear wheel 64 and to tighten it a nut 65; moment of an inhaling of 4050 N · m (4–5 kgfs · м).
4. To establish a gear wheel with the bearing in a case, previously having greased working surfaces with LITOL-24 lubricant.
5. To wrap a nut of the forward bearing; the moment of an inhaling of 105-115 N · m (10,5–11,5 kgfs · м). To Zakontrit a nut.
6. To grease working surfaces of a lath with LITOL-24 lubricant and to establish a lath in a case of the steering mechanism.
7. To establish lath support 70 in a case, previously having greased working surfaces of support with LITOL-24 lubricant. In support to establish an expansion ring 71, having arranged a ring joint along a lath axis, a basic washer and a spring 74.
8. To tighten bolts a cover 73 to a case of the steering mechanism, previously having established a sealing ring 77. Moment of an inhaling of 20-25 N · m (2–2,5 kgfs · м).
9. To establish on a case pipe antisplash covers 10 and 82 and to fix them by new collars. The mentioned collars are intended for one-time use. At installation of a corrugated antisplash cover to sustain the size of 203 mm from its end face to an axis of a bolt 41.
10. To establish a rubber basic ring 13 on a case pipe, and then to establish in a case pipe a cap 42 with the buffer 43 and to record it a bolt 41. Moment of an inhaling of 20-25 N · m (2–2,5 kgfs · м).
11. The adjusting screw 76 it is necessary to achieve that the moment of rotation of a gear wheel in the range of all course of a lath lay within 0,6–1,7 N · m (0,06–0,17 kgfs · l) with its frequency of rotation of 30 min.-1. If the moment of rotation of a gear wheel does not keep within the specified limits, to reveal and remove the causes of jammings of details, paying special attention to a gear wheel, a lath and support of a lath.
12. To establish in openings of a corrugated antisplash cover a bracket of fastening of drafts assembled with drafts and to fix by bolts 48; the moment of an inhaling of 80-100 N · m (· м). Bolts to zakontrit 8–10 kgfs.


8.3. Steering adjustment

8.5. Spherical hinges of steering drafts