|
4-4-ustanovka-zazhiganiya-na-dvigatelyakh-mod-331-i-3317.html
4.4. Installation of ignition on engines of fashion. 331 and 3317The distributor (with removed by the runner and a cover) the engine of fashion. 331 and 3317
|
|
1 – breaker rychazhok;
2 – textolite pillow breaker rychazhka;
3 – screw of fastening of a contact rack;
4 – breaker cam;
5 – conclusion of a wire of low voltage;
6 – nut of fastening of a shaft of the distributor;
7 – distributor case;
8 – contact rack;
9 – a groove for adjustment of a gap between contacts;
10 – mobile plate of the breaker;
11 – vacuum proofreader |
The adjusting duplicating tags on a flywheel and a case of coupling of the engine of fashion. 331 and 3317
|
|
1 – coupling case;
2 – an adjusting ledge of VMT on a coupling case;
3 – a tag 10 ° to VMT on a flywheel;
4 – a tag 0 ° to VMT on a flywheel;
5 – flywheel |
Installation of ignition on engines of fashion. 331 and 3317 it is produced at a run of the new car 1,5 thousand km. and further through each 15 thousand km.
On engines of fashion. 331 and 3317 distributors of ignition 47.3706 are installed.
Check of a condition of a working surface of contacts of the breaker, their cleaning, lubricant of the distributor are carried out similar to the distributor of ignition of the engine of fashion. 2106 through each 15 thousand km of a run of the car. It is in addition necessary to grease the cam plug, having removed previously a rotor and a felt washer under it.
Adjustment of a gap between contacts of the breaker
| PERFORMANCE ORDER |
| 1. To turn the distributor roller so that the gap between contacts became the greatest. |
| 2. To weaken screws 3 (fig. The distributor (with removed by the runner and a cover) the engine of fashion. 331 and 3317) fastenings of a contact rack 8. |
| 3. To insert the screw-driver into a groove 9 and, bringing closer (or deleting) a contact rack 8 to (from) contact (a) on the lever of 1 breaker, to establish a gap between contacts 0,45 ± 0,05 mm. |
| 4. Upon termination of adjustment to tighten screws 3. |
|
Installation of the moment of ignition at options:
A) The distributor was not removed from the engine
| PERFORMANCE ORDER |
| 1. To uncover the distributor. |
| 2. Rotating a bent shaft, to bring a tokoraznosny plate of the runner to the low-voltage plug of the distributor (to a high-voltage conclusion to a candle of the first cylinder on a distributor cover). |
|
3. Continuing to rotate slowly a bent shaft, to combine a tag 3 on a pulley of a bent shaft with an adjusting pin 1 on the lower cover of distributive asterisks (the duplicating tag 3 (fig. The adjusting duplicating tags on a flywheel and a case of coupling of the engine of fashion. 331 and 3317)
on a flywheel has to coincide with an adjusting ledge 2 on a coupling case). At the same time the piston of the first cylinder will be in a compression step, and to make an advancing of ignition 10 ° (to VMT). |
| 4. To connect a control lamp to the plug of low voltage of the distributor 5 (see rice. The distributor (with removed by the runner and a cover) (it is possible to use any automobile lamp) and to "weight" and to include ignition. To turn the distributor case counterclockwise before short circuit of contacts of the breaker (the lamp will go out). |
| 5. To draw in a finger the runner clockwise and to slowly turn the distributor case in the same direction, the control lamp will not light up yet. |
| 6. To check the accuracy of installation of contacts of the breaker for disconnection, drawing in a cam clockwise and at the same time slightly pressing to it a finger a rychazhok. At the same time the control lamp either will go out, or the luminescence of its thread will decrease. |
| 7. To tighten a nut of the 6th fastening of a shaft of the distributor to the drive case. |
| 8. To install a plastic cover on the distributor and to fix it by two spring latches. |
| 9. To insert the high-voltage wires going from spark plugs according to an operating procedure of cylinders of the engine and taking into account the direction of rotation of a rotor of the distributor. To establish a tip of a high-voltage wire from a candle of the first cylinder in a distributor cover plug nest, located over the low-voltage plug in the case. |
| 10. To insert against the stop the high-voltage wire going from the ignition coil to the central nest of a cover. |
|
B) The distributor was removed from the engine, the bent shaft was turned
| PERFORMANCE ORDER |
| 1. To turn out a candle of the first cylinder, to close an opening for a candle in a head of the block of cylinders a stopper from the crumpled paper and to rotate a bent shaft before pushing out of this stopper, having defined thus the beginning of a step of compression in the first cylinder. |
| 2. To uncover the distributor. |
| 3. Rotating the roller of the distributor to bring a tokoraznosny plate of the runner to the low-voltage plug. |
| 4. To insert a distributor shaft into the distributor drive case on the engine. |
| 5. To turn the distributor roller for the runner before combination of thorns of the floating coupling with a roller groove in the case of the drive of the distributor and to enter them into gearing. It is necessary to consider that thorns of the floating coupling of the roller of the distributor and a reciprocal groove in the drive are displaced concerning a symmetry axis aside. Therefore to install the distributor, without having turned previously the runner a tokoraznosny plate towards the low-voltage plug, it will not be possible. Further installation of ignition is made according to points 3-10. |
|
Prevention
Direction of rotation of a rotor of the distributor of ignition of 47.3706 engines of fashion. 331 and 3317 counterclockwise.
Operating procedure of cylinders of engines 1-3-4-2.
For installation of earlier ignition it is necessary to turn the case of the distributor of ignition clockwise, and later – counterclockwise.
|
|
